1、濟南專業防水http://www.tianyujian.com/談到應采用針穿刺法每100平米刺三個點，用尺測量其高度，取其平均值，成膜厚度應大于2毫米，穿刺時應用彩筆做標記、以便修補。
Jinan professional waterproof talked needle method should be used to stab three points per 100 square meters, with a ruler to measure the height, the mean value, film thickness greater than 2 mm, use crayons puncture mark for repair.
2、在濟南專業防水施工中，監理人員可到施工現場將攪拌好的料，分多次涂刷在平整的玻璃板上，成膜厚度1.2－1.5毫米，放置7天后，在1％的堿水中浸泡7天，然后在50℃土 2℃烘箱中烘24小時，做啞鈴型拉伸實驗，要求延伸保持率達到80％（無處理為 200％）。如達不到標準，說明在施工中乳液摻加比例不足。
Jinan professional waterproof construction, construction site supervisors can to the stirred materials, in multiple brushing on a flat glass plate, a film thickness of 1.2-1.5 mm, for 7 days, soaked in 1% of alkaline water 7 days, then bake at 50 ℃ earth 2 ℃ oven for 24 hours, do dumbbell-shaped tensile test, it requires extending retention rate of 80% (no treatment is 200%). Not up to standard as described in the construction of the emulsion adding under-represented.
3、濟南專業防水介紹將涂料分多次涂刷在水泥塊上，成膜厚度1.2－1.5毫米，放置7天，放入1％堿水中浸泡7天，不分層，不空鼓為合格。
Jinan professional waterproof describes the coating in multiple brushing the concrete blocks, a film thickness of 1.2-1.5 mm, for 7 days, add 1% alkaline soak seven days, not hierarchical, not hollowing qualified.
4、濟南專業防水http://www.tianyujian.com/建議在有條件下，應用儀器檢測，其方法是將涂料按比例配好，分多次涂刷在玻璃板上（玻璃板先打蠟），厚度為 1.5毫米，靜放7天，然后放人烘箱內50℃±2℃烘24小時，取出后放置3小時，做不透水實驗，不透水性為0.3MPa，保持30分鐘無滲漏為合格。
Jinan professional waterproof conditionally recommended application equipment testing, the method is to paint with a good pro rata, in multiple brushing on the glass (glass before waxing) and a thickness of 1.5 mm, quiet place seven
days, then to release the oven 50 ℃ ± 2 ℃ bake 24 hours, place three hours after the removal, do impervious experiments, impermeability to 0.3MPa, for 30 minutes without leakage in compliance.